包装印刷产业网

美国泰乐TYLER进口不锈钢磁力泵 

I：进口不锈钢磁力泵概述：

磁力泵由泵、磁力传动器、电动机三部分组成。关键部件磁力传动器由外磁转子、内磁转子及不导磁的隔离套组成。

当电动机带动外磁转子旋转时，磁场能穿透空气隙和非磁性物质，带动与叶轮相连的内磁转子作同步旋转，实现动力的无接触传递，将动密封转化为静密封。由于泵轴、内磁转子被泵体、隔离套*封闭，从而*解决了“跑、冒、滴、漏”问题，消除了炼油化工行业易燃、易爆、有毒、有害介质通过泵密封泄漏的安全隐患，有力地保证了职工的身心健康和安全生产。

II：进口磁力泵的工作原理

将n对磁体(n为偶数)按规律排列组装在磁力传动器的内、外磁转子上，使磁体部分相互组成完整藕合的磁力系统。当内、外两磁极处于异极相对，即两个磁极间的位移角Φ＝0，此时磁系统的磁能zui低；当磁极转动到同极相对，即两个磁极间的位移角Φ＝2π/n，此时磁系统的磁能zui大。去掉外力后，由于磁系统的磁极相互排斥，磁力将使磁体恢复到磁能zui低的状态。于是磁体产生运动，带动磁转子旋转。

III：进口不锈钢磁力泵的优点介绍:

磁力泵是一种通过磁力传动器(磁力联轴器)来实现无接触力矩传递从而以静密封取代动密封，使泵达到*无泄漏。由于泵轴、内磁转子被泵体、隔离套*封闭，从而*解决了“跑、冒、滴、漏”问题，消除了炼油化工行业易燃、易爆、有毒、有害介质通过泵密封泄漏的安全隐患，有力地保证了职工的身心健康和安全生产。

同使用机械密封或填料密封的离心泵相比较，磁力泵具有以下优点：

1．泵轴由动密封变成封闭式静密封，*避免了介质泄漏。

2．无需独立润滑和冷却水，降低了能耗。

3．由联轴器传动变成同步拖动，不存在接触和摩擦。功耗小、效率高，且具有阻尼减振作用，减少了电动机振动对泵的影响和泵发生气蚀振动时对电动机的影响。

4．过载时，内、外磁转子相对滑脱，对电机、泵有保护作用。

当磁力传动器的从动部件在过载情况下运行或转子卡死时，磁力传动器的主、从动部件会自动滑脱，保护机泵。此时磁力传动器上的永磁体在主动转子交变磁场的作用下，将产生涡损、磁损，造成永磁体温度升高，磁力传动器滑脱失效。

IIII：进口不锈钢磁力泵参数

进口14mm~100mm-出口10mm~80mm
流量: 1.2m3/h-60m3/h
级数: 2-10
扬程: 5m-50m
吸程: 3-6m
转速: 2900r/m
电机功率: 0.12kw~18.5kw
适用介质:酸，碱液，油类，稀有贵重液，镀液，挥发性液体 
电压:220/380V
材质:不锈钢

IIIII:不锈钢磁力泵应用:

不含固体颗粒腐蚀液体、强酸、强碱、乙醇、漂白剂、照相液、xiao酸、盐酸、氢氟酸、醋酸、氢氧化纳、丙酮、四氧乙烷、海水、盐水等

The United States imports of stainless steel pump TYLER Taylor

I: imported stainless steel magnetic pump overview:

The magnetic pump consists of a pump, magnetic actuators, motors of three parts. Key components of magnetic actuator by the external magnetic rotor sleeve, inner magnetic rotor and non magnetic components.

When the motor drives the outer magnetic rotor, the magnetic field can penetrate the air gap and non-magnetic material, driven by the magnetic rotor and impeller connected for synchronous rotation, to achieve non-contact power transmission, the dynamic seal into static seal. As the shaft, the rotor is within a magnetic pump, isolated sets of compley closed to compley solve the problem of "run, run, drip, leak, remove the oil refining chemical industry flammable, explosive, toxic and harmful media through the pump seal leakage security risks, effectively ensure the workers health and safety of.

II: imported magnetic pump working principle

N of the magnet (n is even) arranged according to the laws in the magnetic clutch assembly inside and outside the magnetic rotor, the magnet part consisting of magnetic coupling system. When the inside and outside the two poles in different relative displacements, two poles between the angle phi = 0, the lowest energy magnetic system; when rotates to the relative displacement of two poles, pole angle between phi = 2 pi /n, the maximum magnetic energy of magnetic system. Remove the external force, due to the magnetic system of magnetic poles repel each other, magnetic magnet will return to the lowest energy state. Thus, the magnet generates motion to drive the rotor to rotate.

III: introduction of the advantages of imported stainless steel magnetic pump:

Magnetic pump is a magnetic actuator (through magnetic coupling) to achieve non-contact torque transmission to replace the static seal dynamic seal, the pump compley without leakage. As the shaft, the rotor is within a magnetic pump, isolated sets of compley closed to compley solve the problem of "run, run, drip, leak, remove the oil refining chemical industry flammable, explosive, toxic and harmful media through the pump seal leakage security risks, effectively ensure the workers health and safety of.

Compared with the centrifugal pump with mechanical seal or packing seal, the magnetic pump has the following advantages:

1 pump shaft from the dynamic seal into a closed static seal, compley avoid the leakage of the media.

2 no independent lubrication and cooling water, reducing energy consumption.

3 by coupling drive into a synchronous drive, there is no contact and friction. The utility model has the advantages of low power consumption and high efficiency, and has the function of damping and damping, which reduces the influence of the motor vibration on the pump and the influence of the pump cavitation vibration on the motor.

4 when the overload, the inner and outer magnetic rotor relative slip, the motor, pump protection.

When the magnetic actuator driven components running in case of overload or rotor stuck, magnetic clutch master and slave unit will automatically slip to protect the pump. The magnetic drive permanent magnet on the rotor in the active role of the alternating magnetic field, will produce eddy loss, magnetic loss, resulting in permanent magnet temperature, magnetic clutch slip failure.

IIII: imported stainless steel magnetic pump parameters

Import 14mm~100mm- export 10mm~80mm

Flow: 1.2m3/h-60m3/h

Series: 2-10

Lift: 5m-50m

Suction process: 3-6M

Speed: 2900r/m

Motor power: 0.12kw~18.5kw

Suitable medium: acid, alkali, oil, rare valuable liquid, plating liquid, volatile liquid

Voltage: 220/380V

Material: stainless steel

Application of IIIII: stainless steel magnetic pump:

Not containing solid particles, corrosive liquid acid, alkali, alcohol, bleach, photographic liquid, nitric acid, hydrochloric acid and hydrofluoric acid, acetic acid, sodium hydroxide, four acetone, ethylene oxide, water, salt etc.

guan网：http://www.twvalve。。ｎｅｔ/html/2164.html